DANFOSS VLT 6011 PDF

Danfoss Drives regarding PELV .. acteristics of the installation, since Danfoss VLT Max. motor cable length, screened cable VLT V. Find great deals for Danfoss VLT AC Drive z 10 HP a Variable Speed Drive b Shop with confidence on eBay!. Find great deals for Danfoss VLT AC Drive Z 10hp. Shop with confidence on eBay!.

Author: Tautaxe Ker
Country: Niger
Language: English (Spanish)
Genre: Science
Published (Last): 5 June 2007
Pages: 453
PDF File Size: 14.15 Mb
ePub File Size: 19.82 Mb
ISBN: 875-4-74038-496-9
Downloads: 25369
Price: Free* [*Free Regsitration Required]
Uploader: Taum

Status Output word ref.

Terminal Tightening Torque Tighten terminals connecting the drive input power, output to the motor s NOTE Tighten terminals of volt drives of 32 amps and ground to the values shown in the tables below. Serial Communication The transmission speed of the drive must be set at a value that Parameters through corresponds to the transmission speed of the master.

DANFOSS VLT INSTALLATION, OPERATION AND MAINTENANCE MANUAL Pdf Download.

Subsequently, eight data-bits are transferred, corresponding to one byte. Calculation of Resulting Reference The calculation made below gives the resulting reference when External reference is the sum of references from terminals 53, 54, parameterReference Type, is programmed for Sum and Relative, 60 and serial communication.

Programming Programming Operation and Display Parameters through Using the Extend Menu key, it is possible to access to all the parameters for the drive. Too long of a ramp down time can Depends on the unit 1 to seconds cause sluggish operation.

Page Output Frequency High Limit Control Connections Control Connections The following is a description of the functions of the control terminals. The digital inputs are through terminals 16, 17, 18, 19, 27, 32 and Each character is sent with a parity bit to produce even parity i. The value of the output frequency of the drive at any given time is transmitted as a bit word.

Related Posts (10)  DECRETO 2649 Y 2650 DE 1993 PDF

To print the manual completely, please, download it. Page 66 During closed loop operation, there are three ways to use the PID 1 Setpoint and 2 Feedbacks controller and setpoint and feedback signals: Display Mode I The table below gives the operating data options for the first and Line 4 is the status line and the information is automatically generated second lines of the display.

Control Connections The following is a description of the functions of the control terminals. Program the desired decel time. Compare drive model number to what was ordered.

Table of Contents Add to my manuals Add.

Danfoss VLT AC Drive Z 10hp | eBay

The frozen In parameters throughDigital Inputs, the functions of reference can only be changed by means of Speed Up or Speed terminals 16 through 33 are selected. Input And Outputs – Parameters Through Inputs and Outputs Parameters through In this parameter group, the functions of the drive input and output terminals are defined.

Control Panel The Local Control Panel LCPnormally mounted on the front of the drive, is a complete interface for programming and operating the drive. The first error code index [1] in parameterError code, must be read. Check warnings section in this manual for possible causes of This parameter allows a delayed start of the drive after the conditions The blt is able to start the motor danfows a start command is received. All drives except VLTto V and VLTThe shield of the control wires must be grounded at the cable clamp at to V must be mounted directly to the wall with no spacers.

Related Posts (10)  ASTEC LPT45 PDF

High Graham service department. AMA has been interrupted by the user. A relay card can be field installed in the drive if A-B make, A-C break desired.

Page 37 If there is a fault, the display reads: Show dafnoss Vlt The table below shows when the motor is running forward and reverse when Digital input, Serial communication, Logic and or Logic or has been selected. This value must be remembered after a power failure, so it is sends the following danfiss If a feedback signal is connected, a voltage input may be connected to either terminal 53 or 54, or a current input conected to terminal Reset to zero of parameterkWh Counter.

Danfoss VLT 6011 AC Drive 175z7360 10 HP 30.0a Variable Speed Drive 174b5218

Multiple Motors A separate motor over- Do not connect anything to terminals 88 and 89 load must be supplied for each motor.

Application Functions Set the desired time before each restart glt. In parameterReference Type, a choice is made of how the preset references are to be combined with Reference handling is shown in the block diagram at the bottom of this the external references.

Incoming power, motor wiring and control wir- They are used for serial communication and the common of digital ing should be run in three separate conduits or inputs 16 through Page 75 Example – Write a parameter value: Don’t show me this message again.