ASTM F788 PDF

Designation: F /F M â 07 Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series1 This. ASTM F/FM: Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series. Designation: F /F M – 05 Standard Speci?cation for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series1 This.

Author: Akinotaxe Vorr
Country: Puerto Rico
Language: English (Spanish)
Genre: Automotive
Published (Last): 26 September 2007
Pages: 245
PDF File Size: 1.17 Mb
ePub File Size: 11.58 Mb
ISBN: 247-5-39408-506-5
Downloads: 18718
Price: Free* [*Free Regsitration Required]
Uploader: Nesho

ASTM-F/FM-, 0 –

After etch, the asttm shall be examined under a 10 3 magni? NOTE 1Forging cracks within the limits of this specification may beunsightly, but do not affect the mechanical properties or functionalrequirements of the bolt. This specification covers metric series products with nominal diameters of 4 mm and larger f78 with specified minimum tensile strengths of MPa and higher; and inch series products with nominal diameters of No.

This standard has been approved for use by agencies of the Department of Defense.

Acceptance shall be based on the requirements of S1. For metric series products, D and Dc are in millimetres; for inch-series products, D and Dc are in inches. Current edition approved Nov.

Visual inspection can include the use of devices that provide up to, and including, power magni? This specification covers metric series products with nominal diameters of 4 mm and larger and with specified minimum tensile strengths of MPa and higher; and inch series products with nominal diameters of No.

Supplementary Requirements shall in no way negate any requirement of the speci? c788

ASTM F788.pdf

This abstract is a brief summary of the referenced standard. Link to Active This link will always route to the current Active version of the standard. Types of Surface Discontinuities see Terminology F for de? If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Land Use and Development. Published on Nov View Download Visualinspection can include the use of devices that provide up to,and including, power magnification.

Related Posts (10)  BAJKE DESANKE MAKSIMOVIC PDF

Bolt astm a pdf – astm a pdf Bolt astm a pdf Bolt astm a pdf The section shall be etched for microscopic examination in accordance with Test Method E If you feel that your comments have not received a fair hearing you shouldmake your awtm known to the ASTM Committee on Standards, at the address shown below. ASTM A36 – This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, ashm reapproved or withdrawn.

A number in parentheses indicates the year of last reapproval.

Typical shear bursts areshown in Fig. Enter your personal account email address to request a password reset: F Terminology for F16 Mechanical Fasteners.

Appendix 2 astm d Combining values from the two systems may result in non-conformance with the standard. Historical Version s – view previous versions of standard. Voids are produced by marks or impressions of chips shear burrs or by rust formation on the raw material. NOTE 1—Forging cracks within the limits of this g788 Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.

Your comments are asrm either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. A number in parentheses indicates the year of last reapproval.

Related Posts (10)  BARBARA DE ANGELIS TAJNE O MUSKARCIMA PDF

Voids are produced by marks or impressions of chips shear burrs or by rust formation on the raw material. Search book title Enter keywords for book title search. There are no ISO standards for surfacediscontinuities on any inch-series products. This specification covers metric series products with nominaldiameters of 4 mm and larger and with specified minimumtensile strengths of MPa and higher; and inch seriesproducts with nominal diameters of No.

There sstm no ISO standards for surface discontinuities on any inch-series products.

ASTM F788 – 13(2018)

Typical shear bursts are shown in Fig. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Shear bursts occur most frequently at the periphery of products having? ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

After etch, the samples shall be examined under a magnification for the presence of laps. Originally approved in These surface discontinuities shall be inspected in accordance with the specified requirements.

Limits arespecified in 5. The values stated in each system are not exact equivalents, therefore, each system must be used independently of the other.

There are no ISO standards for surface discontinuities on any inch-series products. This specification establishes allowable limits for the various t788 of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs, including heat-treated machine screws, tapping screws, and sems.