ASTM D5587 PDF

Tear test of Fabric by trapezoid method to ASTM D ASTM D covers the measurement of the tearing strength of textile fabrics by the trapezoid tear test using a constant-rate-of-extension-type (CRE) tensile. ASTM D Tearing Strength of Fabric by. Trapezoid Procedure. • Scope – this test method describes the determination of the tearing strength of fabrics by the.

Author: Keshura Dahn
Country: Venezuela
Language: English (Spanish)
Genre: Education
Published (Last): 19 December 2005
Pages: 383
PDF File Size: 5.62 Mb
ePub File Size: 19.82 Mb
ISBN: 112-5-44329-586-3
Downloads: 28612
Price: Free* [*Free Regsitration Required]
Uploader: Shakajora

Description Literature Contact Us This standard mainly applies to most woven textile fabrics, but can be applicable to fabrics produced by other techniques.

ASTM D5587 Tearing Strength of Fabrics by Trapezoid Procedure

Onsite Training At Your Facility. Next Checking to see if you are a returning visitor…. The method specifies a procedure to determine the tear force of textile fabrics using the trapezoid method.

The highest peaks appear to reflect the strength of f5587 yarn components, individually or in combination, needed to stop a tear in fabrics of the same construction. If any of d55587 modications are used, state the method of modication in the report.

It is useful for estimating the relative tear resistance of different fabrics or different directions in the same fabric. The reported value obtained is not directly related to the force required to initiate or start a tear. Historical Version s – view previous versions of standard.

For x5587 test, it is important to have an increased test data rate to ensure the capture a high number of data points.

It is important to review ASTM D in order to fully understand the test setup, procedure, and results requirements. A superscript epsilon e indicates an editorial change since the last revision or reapproval.

ASTM D Tearing Strength Fabrics by Trapezoid Procedure – Instron

When specimens are to be tested wet, take the specimens from areas adjacent to the dry test specimens. The test results from the laboratories involved should be compared using a statistical test for d55877 data, at a probability level chosen prior to the testing series. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Related Posts (10)  BEHRINGER SNR 2000 PDF

The fabrics may be untreated, heavily sized, coated, resin-treated, or otherwise treated. Sampling adtm Test Specimens 7. Force range of 5 kN to kN 1, lbf tolbf Adjustable test space The most popular choice for static tension and compression tests These dual column testers are available in both tabletop and floor standing models.

Mark each specimen with an isosceles trapezoid template see Figs. There were sufficient differences related to the fabric type and structure to warrant listing the components of variance and the critical differences separately. Subscribe to Instron News!

Hold the short edge d5587, and let the remaining fabric lie in folds. We are confident that we have what you are looking for.

Tear Strength of Fabrics – Trapezoid Procedure

V5587 are provided for testing specimens with or without wetting. The nonparallel sides of the marked trapezoid are d55887 in parallel jaws of a tensile testing machine. The values stated in inch-pound units may be approximate. This test method allows the use of the CRT-type tensile machine when agreed upon between the purchaser and the supplier. The specimen is slit at the center of the smallest base of the trapezoid to start the tear. Consequently, these test instruments may be used when agreed upon between the purchaser and the supplier.

Record values as read from the direct-reading scale to the nearest 0. Contact Us View Accessories Catalog. For most fabrics this time period will be about 1 h. The values stated in inch-pound units may be approximate. If a bias is found, either its cause must be found and corrected, or the purchaser and the supplier must agree to interpret future test results with consideration to the known bias. Consequently, these test instruments may be used when agreed upon between the purchaser and the supplier.

Related Posts (10)  LIBRO LA PRINCESA QUE CREIA EN CUENTOS DE HADAS PDF

The fabrics may be untreated, heavily sized, coated, resin-treated, or otherwise treated.

ASTM D – 15 Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure

The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in v5587 standard. The fabrics may be untreated, heavily sized, coated, resin-treated, or otherwise treated. Ensure specimens are free of folds, creases, or wrinkles.

Users of previous versions of software such as Bluehill 2 and Bluehill 3 can easily upgrade to the newest version of Bluehill. Bluehill Universal Software is built from the ground-up for touch asm and an intuitive user experience.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

A rectangular specimen is marked and astk so that it can be loaded in the grip faces at an angle, allowing a tear to propagate across the specimen.

As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. While manual action grips will work, many prefer pneumatic side action grips for ease of use, productivity, and better repeatability.