This standard is issued under the fixed designation A /A M; the 1 This specification is under the jurisdiction of ASTM Committee A ASTM A/AM: Standard Specification for Steel, Sheet and Strip, Heavy- Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural. Find the most up-to-date version of ASTM A at Engineering

Author: Aram Gasida
Country: Italy
Language: English (Spanish)
Genre: Politics
Published (Last): 19 December 2017
Pages: 409
PDF File Size: 13.52 Mb
ePub File Size: 16.54 Mb
ISBN: 574-3-22877-805-8
Downloads: 99840
Price: Free* [*Free Regsitration Required]
Uploader: Kigarr

Approved March 1, Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

For strip over 8 in.

Cut Edge and 1-in. The analysis shall be from a test sample preferably taken during the pouring of the heat or cast. For nominal thickness, the tolerance is divided equally over and under. The sampling may be facilitated by folding the sheet both ways, so that several samples may be taken at one drilling. Please read our License Agreement regarding materials data and our Privacy Policy.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Cut Edge and 3? Or if you don’t have an account with us yet, then click here to register. Originally approved in Link to Active This link will always route to the current Active version of the standard.

Therefore, users must analyze chips taken from the steel in the condition in which it is received from the steel manufacturer.


Cast a6635 heat analysis shall be made to determine the conformance with the requirements. Such a deviation is obtained by placing an 8-ft straightedge on the concave side and measuring the greatest distance between the strip edge and the straightedge. However, under SI, the preferred term is mass. Over 8 to 12, incl Crown Tolerances for Speci?

A superscript epsilon e indicates an editorial change since the last revision or reapproval. The tolerances provided in the table are based on minimum thickness tolerance over, no tolerance under. Combining values from the two systems may result astk nonconformance with this specification.

Dimensions and Tolerances 8. All Widths A All Widths. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Conformance to Annex A1 is mandatory when the “M” specification is used.

This table does not apply to the uncropped ends of mill edge coils. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values.

NOTE 2—Micrometers used for measurement of thickness shall be constructed with anvils and spindles having minimum diameters of 0. The purchaser is advised to discuss this change with the supplier.

Product analysis is appropriate on these types of steel only when misapplication is apparent, or for copper when copper steel is speci? Retests and Disposition of Non-Conforming Material These coils are normally produced from rimmed, capped, or semi-killed steel.

Such a deviation is obtained by placing a mm straightedge on the concave side and measuring the greatest distance between the strip edge and the straightedge. However, unless the order speci? Materials and Manufacture 5.

Related Posts (10)  CD4511BCN DATASHEET PDF

AK Steel ASTM A and A Hot Rolled Carbon Steel, Structural Steel (SS)

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the z635 of infringement of such rights, are entirely their own responsibility. Micrometers with pointed tips are not suitable for thickness measurements. These elements are considered as incidental and are not normally determined or reported. When different grades of strand-cast steel are sequentially cast, identi?

ASTM A635 Grade 1018

Size Limits, Coils Only. NOTE 1—Camber is the deviation of a side edge from a straight line. Depending upon the angle of the bevelled edge cut, the width of the narrow surface of the cut-edge coil may be less than the minimum ordered width. We appreciate your input. We also ask that you refer to MatWeb’s terms of use regarding this information. Structural steel may be ordered when the coils are intended for conversion to plate a35.

For steels other than non-killed capped or rimmedproduct analysis may be made. To see MatWeb’s complete data sheet for this material including material property data, metal compositions, material suppliers, etcplease click the button below. Hot roll manufacturer de?