There are precautions provided in ASTM A/AM that should be considered to prevent embrittlement, as well as selecting steels with appropriate. Practice ASTM A provides guidance on safeguarding against warpage and be stress relieved per the guidelines provided within ASTM A, Section 6. ASTM A / AM Standard Practice for Safeguarding Against Embrittlement of Hot-Dip Galvanized Structural Steel Products and Procedure.

Author: Sazahn Taushakar
Country: Maldives
Language: English (Spanish)
Genre: Relationship
Published (Last): 2 April 2016
Pages: 287
PDF File Size: 7.16 Mb
ePub File Size: 12.10 Mb
ISBN: 241-6-51934-158-2
Downloads: 63464
Price: Free* [*Free Regsitration Required]
Uploader: Nelmaran

Students Click Here Join Us! By joining you are opting in to receive e-mail. If so, how do you handle the testing requirements? It is the responsibility of the designer and fabricator to ensure the product has been properly designed and built before the hot-dip galvanizing process supporting specifications.

The requirements in the specification facilitate the production of a high-quality zinc coating and are similar to those found in A and A Other materials that can be galvanized include continuous cast slabs, steel atsm iron castings, and wrought iron. Avoid Susceptible Thin Sheet Steels Steel invariably contains internal stresses induced at the mill from rolling operations used to bring structures, plate, and sheet to the final thickness.

Within the text of this practice and where appropriate, SI units are shown in brackets. Join your peers on the Internet’s largest technical engineering professional community.

Inspector Listing – Non-U. That’s a standard for safeguarding against embrittlement of hot-dip galvanized steel. However, there are a few additional requirements for galvanized rebar.

However, if the galvanizer has to perform additional work in order to prepare the product for hot-dip galvanizing, such as drilling holes to facilitate drainage or venting, the galvanizer will communicate and resolve the issue with the customer. Embrittlement is not a common occurrence, however, and this discussion does not imply that galvanizing increases embrittlement where good fabricating and galvanizing procedures are employed. Optimize Welding Before Hot-Dip Galvanizing Welding results in significant residual stress in small areas of an assembly due to the extreme temperature differences experienced.


Eddy-current-type thickness measurement is a non-destructive test measuring variations in the impedance of an eddy-current inducing coil caused by coating thickness variations. Finally, the adherence requirement is for the entire coating to have a strong adherence throughout the service life of the galvanized steel. The specification requirements for coating thickness only contain minimums, there is no maximum coating thickness limitation in the specification.

The design of the product and selection of proper steel for its suitability to withstand normal galvanizing operations is the responsibility of the designer and fabricator. The material categories covered in the specification include structural steel and plate, strips and bars, pipes and tubing, and wires.

ASTM A384 Recommendations

asgm Conditions of fabrication may induce a susceptibility to embrittlement in certain steels that can be accelerated by galvanizing. This specification covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers, nuts, and special threaded fasteners applied by the hot-dip coating process. Whenever different analyses of steel or different surfaces of steel are united in an assembly the galvanized wstm is not generally uniform in appearance.

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. The specification requirements for coating thickness only contain minimums, there is no maximum coating thickness limitation in the specification. Fabrications can have more than one material category, such as a frame assembly.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A second type asym embrittlement, hydrogen embrittlement, is recognized when stresses are applied to the steel in use.

However, the AGA does provide a compilation of specifications pertinent to galvanizing. Download Now White Paper: I don’t know if it’s a case of 1 just never having anyone spec A astn or 2 I’m just not aware that it asttm place or 3 it has been spec’d on other jobs but no one paid any attention to the testing part. Heat analysis shall be used to determine the percentage of asstm, manganese, phosphorus, sulfur, vanadium, nickel, chromium, molybdenum, columbium, and copper for the required chemical composition.


Active view current version of standard.

ASTM Specifications | American Galvanizer’s Association

The requirements of this specification are very similar to those in A, except for asym addition of threaded products and embrittlement requirements. Historical Version s – view previous versions of standard. A requires a continuous, smooth, and uniform finish with no uncoated areas including on the threads or issues that interfere with its intended use.

The specification outlines three acceptable forms of touch-up: The purpose of the calculation is to aastm justification for the purchase of a higher initial cost system with a low life-cycle cost over an initially less expensive coating which has high future costs. This specification covers cold-formed welded and seamless carbon steel round, square, rectangular, or special shape structural tubing for welded, riveted, or bolted construction of bridges and buildings, axtm for general structural purposes.

The following can cause warpage and distortion: The design and fabrication of the product to be galvanized are the responsibilities of the designer and the fabricator.

ASTM A143/A143M – 07(2014)

Embrittlement of steel shapes, steel castings, threaded articles, and hardware items shall be tested using a bend testa universal testing machine, or by means of a press with the load applied slowly, until fracture of the galvanized test specimen occurs. Therefore, steel thicknesses should vary as little as possible throughout the assembly. Reasons such as off-topic, duplicates, flames, illegal, vulgar, or students posting their homework.

Requirements concerning the renovation of uncoated areas after initial hot-dip galvanizing are contained within the material specifications A, A, A Inch-pounds and SI units are not necessarily exact equivalents.